They are making several good points on How to Install a Bathtub overall in this great article in the next paragraphs.
Setting up a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably hard project. If the old tub is readily accessible, the project can move easily; if you need to open up a wall surface to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly need a helper to leave the old tub and set in the new one. Make sure you have actually certified on your own for the job and are comfortable attempting it. Rather than employing a professional to take over a halfway-completed job, it is much better to consider employing one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This article will certainly help you mount a brand-new tub in your shower room if you have currently acquired a brand-new bathtub and also do not require to alter the plan of your previous supply of water pipes.
Your tools and material list need to make up the following:
Planning for the Installation
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome because of the limited gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will come from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the tub in the needed placement. The wood boards are useful in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bath tub till the level reads level.
To install faucets, fit all-time low of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the other faucet.
Turn on the water system and check all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the tub and also check the overflow electrical outlet and also the typical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bathtub should wait till the tub has been used at least when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type needs to be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall in between the bath as well as the tiling, leading to issues with wetness and possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can fracture fairly early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very fascinated by How to Install a Bathtub Yourself and I'm hoping you enjoyed our post. For those who liked our blog entry please remember to share it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Get Estimate